High compression 88mm piston kit containing aluminium piston, gudgeon pin, circlips and piston ring set. Combine with 88mm barrels to increase capacity and performance of Le Mans 1, Le Mans 2 and Le Mans 3 models. This kit can also be fitted to low compression 88mm models (e.g. 1000 SP) to increase performance

Dome Height Approx. 6.5mm

 2 in stock

 28060450 GU28060450 28 06 04 50
 2806 0450 2806.0450 28.06.04.50

High pressure black fuel line / fuel line, can be used to replace fuel line on other models with 6mm ID fuel lines

This high pressure fuel hose is rated to 225 PSI. It has been designed for use with Modern Chemically Aggressive Bio-Ethanol Enriched Petrol Formulations (E5 & E10) As per currently served petrol pump petrol. Confirms to SAE J30 R7 and BS AU 108. See FUA00004 for hose clips

 2 in stock

AP8144069

Threaded adaptor connecting oil line to cylinder head

Fits to ENA14660

 2 in stock

 14153660 GU14153660 14 15 36 60
 1415 3660 1415.3660 14.15.36.60

Pair of black tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 1 in stock

Pair of chrome tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 1 in stock

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 1 in stock

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Dizzie bearing

 1 in stock

Crankshaft Sludge Trap Plug

 1 in stock

 12065400 GU12065400 12 06 54 00
 1206 5400 1206.5400 12.06.54.00

Main bearing flange gasket

Also known as Guzzi ref. 05011830

 1 in stock

12011800-z 12011800 GU12011800 12 01 18 00
 1201 1800 1201.1800 12.01.18.00

Complete gasket kit

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12x ENA97624 and 2 x ENA90203

 1 in stock

30999060-z 30999060 GU30999060 30 99 90 60
 3099 9060 3099.9060 30.99.90.60